YAMAMOTO SOUND SUT-02 - $1.400

New product SUT-02 are new development of our company and a Step up transformer for low impedance MC
 cartridges. Although it is on sale in a Step up transformer called SUT-01 and popularity has already been
 acquired at our company, it is a Step up transformer of the establishment meter which succeeded the
 technology of the SUT-01, and was miniaturized more, and also raised the shield effect, vibration proof
 performance, etc.
  Usually, although the Step up transformer for stereo 2ch. is manufactured in one case, it is the greatest
 feature for SUT-02 to have separated two transformers completely, and to have enclosed and made each the
 firm case. The case which began to delete the block of the aluminum alloy like understanding, and became
 brave is manufactured with a lower right photograph, a transformer unit is enclosed there, and it is
 wiring by the shortest distance. We are filled up with the high insulating epoxy resin with big intensity
 of the type heated and stiffened in this case. Beautifully, a transformer case gives champagne gold color
 alumite finish strong also against a secular change, and is considering it as high-definition finish. 
  It becomes possible to pick up without not influencing a transformer unit almost by vibration, but being in
 the state where it was released from the influence of a detailed vibration, and also leaving the very 
 small signal of MC cartridge by this.
  The transformer unit of SUT-02 succeeds the core and winding technology which were acquired by SUT-01, 
 adopts the super permalloy core of the same 100-micron thickness, and is wounding it using the
 insulating paper of Teflon. It has changed, as conventional SUT-01 changed the section which had adopted
 the core with big outer diameter form, enlarged a cross-section area more, made an outer diameter small
 and a magnetic passage shortened in it. It also enabled it for an outer diameter to become small and to
 include in the inside of amplifier by this. Moreover, the winding of a transformer does not take out a
 tap but input and output are suppressing degradation of the SN ratio by an idle terminal etc. as one
 terminal. A Step up transformer is a section handling the smallest signal in the field of an audio.
 Although various setting bases etc. are manufactured at our company, in order to lose the influence 
of vibration to each, it keenly realizes that it is most important that the intensity about which the product 
itself became brave is high. Therefore, the case which became brave so that it might hardly be influenced by
 vibration was adopted as SUT-02. Since the screw of M2.6 is turned off to four corners in the bottom side of this
 case, it is also possible to stop and use the base of liking etc. for this section in person.
Moreover, also when incorporating in amplifier, it can fix using this screw hole. Moreover, as for the impedance
 of the cartridge which suits SUT-02, 1-5ohm, and its amplification factor are designed 20 times. Since the output level
 of the low impedance type MC cartridge is large recently, a little we have set up the Step up ratio lowness.
 This becomes comparatively easy to use the volume level of a preamplifier.

The method of wiring of SUT-02

Please perform the connection method of SUT-02 as follows. From a grounding terminal wires right and left
 separately, two ground wires are required. The ground wire by which it is coming from the player may
 not be as so as the case where to connect with the grounding terminal of a transformer case is better.
 Please choose the better one by the system used.

SUT-02 Specifications

Form: The Step up transformer for low impedance MC cartridges
Step-up ratio: 1:20
Conformity impedance: 1-5ohms
Frequency characteristic: 10 to 100,000 Hz
The material currently used: A 100-micron thickness super permalloy troidal core and Teflon
 insulating-paper adoption, It is aluminum alloy shaving and a case is filled up with an epoxy resin,
 An input-and-output pin jack adopts the high reliance type of Teflon insulation chromium copper of our original.
Outside dimension: 60(W) x80(D) x64(H) mm (only a case is 60x60x64mm)

Weight : 580g/one piece